Replacing AQUAPHOR Morion Filters Yourself

To replace the filters in your AQUAPHOR Morion 101 yourself, follow the instructions below:

If you are only going to replace the K5 and K2 modules, it is recommended to do so every 6 months, depending on the quality of the incoming water.

1. Shut off the connection point to the water supply.
2. Open the clean-water faucet to release the pressure.
3. Remove the K5 and K2 modules. With one hand, press the locking button all the way down and hold it (the button is located above each module); with the other hand, turn the module counterclockwise.
4. Swap the K5 and K2 modules for the flushing procedure. Place K2 under the black button and K5 under the blue button.
5. In place of the membrane, install the plug or use the old K2 module. To remove the membrane module, also press the red button. Place the membrane in a container, as water will flow out of it.
6. The K7 (or K7M) module stays in place.
7. Turn on the water supply to the filter. Open the clean-water faucet. Adjust the water flow so that it runs in a thin, threadlike stream. The flushing time is 10 minutes.
8. Close the clean-water faucet and let the filter stand for 10 minutes so that the modules become saturated with water.
9. Open the clean-water faucet. Adjust the water flow so that it runs in a thin, threadlike stream. The flushing time is 30 minutes.
10. Close the clean-water faucet and shut off the connection point.
11. Install the K5 and K2 modules in their working positions. K5 should be installed under the black button, and K2 under the blue button.
12. Put the membrane back in its place.
13. You can now use the filter.

If you need to replace the K5, K2, and K7 (or K7M) modules, follow the previous recommendation, but make the following change to step 6:

6. In place of the old K7 (or K7M) module, install a new K7 (or K7M) module. The K7M module is located under the white locking button.

Continue following the remaining steps of the instructions to complete the process of replacing the cartridges and membrane in the AQUAPHOR Morion 101 filtration system. Remember that the K7 (or K7M) module is recommended to be replaced once a year.

If you are replacing the K5, K2, K7 (or K7M) modules and the RO-50S membrane module in the AQUAPHOR Morion 101 filtration system, follow these instructions:

1. Shut off the connection point to the water supply.
2. Open the clean-water faucet to release the pressure.
3. Remove the K5 and K2 modules. With one hand, press the locking button all the way down and hold it (the button is located above each module); with the other hand, turn the module counterclockwise.
4. Swap the K5 and K2 modules for the flushing procedure. Place K2 under the black button and K5 under the blue button.
5. In place of the membrane, install the plug or use the old K2 module. To remove the membrane module, also press the red button. Place the membrane in a container, as water will flow out of it.
6. In place of the old K7 (or K7M) module, install a new K7 (or K7M) module. The K7M module is located under the white locking button.
7. Turn on the water supply to the filter. Open the clean-water faucet. Adjust the water flow so that it runs in a thin, threadlike stream. The flushing time is 10 minutes.
8. Close the clean-water faucet and let the filter stand for 10 minutes so that the modules become saturated with water.
9. Open the clean-water faucet. Adjust the water flow so that it runs in a thin, threadlike stream. The flushing time is 30 minutes.
10. Close the clean-water faucet and shut off the connection point.
11. Swap the K5 and K2 modules back, that is, install them in their working positions. K5 should be installed under the black button, and K2 under the blue button.
12. Install the new RO-50S membrane module. Disconnect the drain tube with the elbow fitting from the old module: pull the locking clip out from under the plastic tube, press on the end of the plastic tube, and pull the elbow out of the membrane.
13. Install the new membrane in the manifold, under the red button.
14. Connect the drain tube’s elbow fitting to the new RO-50S membrane. Moisten the end of the elbow with water and insert it into the membrane. Install the locking clip.
15. Open the connection point.
16. Flush the membrane module. To do this, first drain the water from the tank by opening the clean-water faucet and waiting until the water begins to run in a thin stream. Then close the clean-water faucet and let the tank fill up; this will take about 1 hour. Repeat the tank-draining procedure once more.
17. The membrane is now flushed and ready for use. You can use the filter.

Please note that the RO-50S membrane module is recommended to be replaced every 1.5-2 years, depending on the operating conditions and water quality. In Israel, the membrane module is usually replaced once every 2.5-3 years.

If you are unable to handle the replacement yourself, we recommend contacting a professional filter installer. You can provide us with your contact details and we will replace the cartridges and membrane in your system.

You can also call us
to order a replacement of your AQUAPHOR Morion filters:
050-3510777